MALOSSI FORCE MASTER 2.1 iGet EURO5 VESPA Primavera & Sprint 150cc 2024-

MALOSSI FORCE MASTER 2.1 iGet EURO5 Primavera & Sprint 150cc 2024-CURRENT (5519025)

Malossi Force Master 2.1 EURO-5 Primavera & Sprint 150cc 2024-CURRENT Euro 5 engine. On a modern scooter, the control module for analyzing the air-fuel ratio is normally connected to the lambda sensor installed on the muffler. This is how the air-fuel ratio is adjusted now.

The Malossi Force Master 2.1 injection module intercepts the signal from the O2 sensor, sends a virtually generated lambda value to the primary control module and thus enables dynamic and, above all, individual control of the air-fuel ratio. It is therefore possible to adjust the air-fuel ratio of the injection between idling and full throttle, essentially for all engine speeds and conditions under which control of the O2 lambda operation could prevent restriction. Thanks to a sophisticated circuit, the electrical interference normally present on the throttle control signal is eliminated, in such a way that the actual degree of opening can be identified more accurately and response times can be significantly improved, which in turn has a positive effect on engine performance and efficiency.

Features:

• Fuel adjustment
• Mapping adjustment ± 14 % at LOW / HIGH / MID
•  8 different mappings
• Speed limiter: + 1,000 rpm
• Lambda emulator
• Temperature range = -20°C +80°C
• Average current consumption <- 200mA
• Minimum operating voltage = +7V
• Maximum operating voltage = +16V
• Protection class = IP65

The Malossi Force Master 2.1 injection module has a total of 8 selectable mappings to use with the original cylinder, the Malossi cylinder as well as combinations of Malossi exhaust systems  / camshaft / air filter and to generate the best possible performance. Extra attention has been paid to improving the user interface by introducing a graphic display that shows the most important parameters of the fuel mixture: Firmware version System status Position of the fuel-mixture curve.

The Malossi Force Master 2.1 injection module is equipped with a Can-Bus to which possible extensions can be applied. You will have to splice in the wiring for this modular. THIS IS NOT PLUG AND PLAY

Scooter West has been a proud distributor of Malossi products since 1995. We 
keep more Malossi part numbers in stock than any other company in North America. 
When it comes to quality performance scooter parts, MALOSSI is the long-standing 
industry leader for price, selection, and quality. All Malossi components are 
made 100% in Italy. All final manufacturing, assembly, and research and 
development is done at their impressive facility in Bologna, Italy. Literally, 
just down the street from Ducati and a 20 minute drive from Ferrari. The quality 
of Malossi components is commonly far superior to comparable original equipment 
components. They are after-all, designed and race-track tested and approved.

Like many other Italian aftermarket companies, Malossi has humble beginnings as 
a small family business sprung from one man's passion. Mr. Ugo Malossi started 
tuning and manufacturing the best performance carburetors in the region under 
the tutelage of his mechanically accomplished father, Armando. In 1957, with the 
vision of Ugo, Malossi was formally born. Ugo's son and daughter are the active 
managers of the company and they share in their father's passion and vision to 
“Always improve.”

**Disclaimer** No Refunds, Exchanges, or Returns on performance items. 
Certain performance items may void your factory warranty. Additionally, some 
performance items may not be suitable for on-road use. Scooter West is not 
responsible for any damages caused by the correct or incorrect installation 
and/or misuse of any performance products. With all this standard legal jargon 
being said, we wouldn't sell anything that we wouldn't install on our own 
scooters. We are blessed to have a Robot running our service department that 
makes sure everything is installed correctly on our personal scooters ;).